Plus2.0 18000mAh 6S1P 22.2V 15C Smart



Part ID 18376
Brand Tattu
Weight 20.00g


Share this part



Parts » Batteries

Plus2.0 18000mAh 6S1P 22.2V 15C Smart by Tattu

No votes yet


Vendor Price USD $354.00 USD $355.00 USD $356.00

Reviews 0



Tattu Plus2.0 18000mAh 6S1P 22.2V 15C Intelligent Lipo Battery with AS150+XT150 plug will give your UAV the enough power for long time to fly. The Version 2.0 is the updated version of Tattu Plus series. 7 LED lights on the battery make it convenient for your use. It is easy to check the service life of the pack. Storage mode will be auto-activated. 

  • Overheat protection
  • Low temperature protection
  • Over voltage protection
  • Over current protection
  • Intelligent Storage:
    • Normal temperature range storage 
    • Above normal temperature storage 60-70℃ (158°F –176°F) 
    • Hot conditions storage 70-80℃ (158°F – 176°F)
  • Local after-sales service(located in Dublin, CA)


  • Minimum Capacity: 18000mAh
  • Configuration: 6S1P / 22.2V / 6Cell
  • Discharge Rate: 15C
  • Max Burst discharge Rate: 30C
  • Net Weight(±20g): 2270g
  • Dimensions: 205.5mm Length x 94.2mm Width x 79.5mm Height
  • Discharge Plug: AS150+XT150 plug
  • Charge Plug: XT90

Tattu Plus 
Tattu Plus 2.0
Fuel Gauge
Yes, the fuel gauge is run by a very accurate coulomb meter and impedance tracking circuit.  This makes the fuel gauge display very precise.
Self Balance in storage mode
Yes, the pack will self balance the individual cells depending on the SOC(State of charge) difference during storage mode
Discharge Low voltage warning
LED Flash Warning
Audible warning system
Discharge over temperature warning
LED Flash Warning
Audible warning system
Cycle life indicator
Defective Pack Warning
if you click the pack button and the fuel gauge shows red L.E.D.s, it is time to replace this pack.
Battery low voltage warning
Yes, if you click the button and the fuel gauge shows yellow L.E.D.s the pack voltage is low and you need to recharge.
Battery storage indicator
Yes, The storage is turned on if you click the button and the fuel gauge shows white L.E.D.s  the pack is in storage mode.
Advanced charging protection
Yes, if the pack individual cell voltage is too low when charging is started,the BMS will limit the incoming charge current to  battery until the voltage is correct, then accept full supplied charge current
Voltage Overcharge Protection
Yes, the overcharge protection circuit will activate when any cell voltage exceeds the factory set failsafe values.
Charging over current protection
Yes, charging over current protection circuit will be activated when charging current reaches factory set failsafe values.  The protection circuit will remain active until charger is disconnected.
Charging short circuit protection
Yes, the protection circuit will cut off charging when it detects that the current reaches the factory set short-circuit protection limit. When protection is triggered all FETs will be turned off.
High Temperature Charge Protection
Yes, if the pack temperature exceeds factory set values It will not charge.  When the pack is back in the correct temperature range it will charge normally
Low Temperature Charge Protection
Yes, if the pack temperature falls below factory set values the pack will not charge.  When the correct temperature is back in range the pack will charge normally.
Secondary Charge Protection
Yes, Tattu Plus 2.0 has a secondary charging protection circuit.  If the first level circuit has a failure, the second level of protection will cut the charging circuit off
IIC communication port
Yes, The IIC communication port is active.  When you connect the batterypack to the computer software the IIC will allow you to read: pack voltage, individual cell voltage, rated capacity after full charge, remaining capacity, capacity percentage, cycle time, tem

  • 1x Tattu Plus2.0 18000mAh